konfigurasi switch S1
ketikan pada commang line interface
S1>en S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#vlan 10
S1(config-vlan)#vlan 20
S1(config-vlan)#vlan 30
S1(config-vlan)#vlan 40
S1(config-vlan)#vlan 50
S1(config-vlan)#vlan 60
S1(config-vlan)#vlan 70
S1(config-vlan)#vlan 80
S1(config-vlan)#vlan 99
S1(config-vlan)#int range f0/1-4
S1(config-if-range)#switchport mode trunk
S1(config-if-range)#switchport trunk native vlan 99
S1(config)#int vlan 99
S1(config-if)#ip add 172.17.10.21 255.255.255.0
S1(config-if)#no shut
S1(config)#spanning-tree mode rapid-pvst
S1(config)#spanning-tree vlan 1,10,30,50,70 root primary
konfigurasi switch S2
S2(config)#int fa0/11
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 10
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config)#int fa0/18
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 20
S2(config-if)#spanning-tree bpduguard enableS2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config)#int fa0/6
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 30
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shut
S2(config-if)#vlan 10
S2(config-vlan)#vlan 20
S2(config-vlan)#vlan 30
S2(config-vlan)#vlan 40
S2(config-vlan)#vlan 50
S2(config-vlan)#vlan 60
S2(config-vlan)#vlan 70
S2(config-vlan)#vlan 80
S2(config-vlan)#vlan 99
S2(config-vlan)#ex
S2(config)#int vlan 99
S2(config-if)#ip add 172.17.20.22 255.255.255.0
S2(config-if)#no shut
S2(config-if)#ex
S2(config)#spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary
S2(config)#spanning-tree mode rapid-pvst
konfigurasi switch S3
S3>en
S3#conf t Enter configuration commands, one per line. End with CNTL/Z.
S3(config)#vlan 10
S3(config-vlan)#vlan 20
S3(config-vlan)#vlan 30
S3(config-vlan)#vlan 40
S3(config-vlan)#vlan 50
S3(config-vlan)#vlan 60
S3(config-vlan)#vlan 70
S3(config-vlan)#vlan 80
S3(config-vlan)#vlan 99
S3(config-vlan)#int range f0/1-4
S3(config-if-range)#switchport mode trunk
S3(config-if-range)#switchport trunk native vlan 99
S3(config)#spanning-tree mode rapid-pvst
S3(config)#spanning-tree vlan 20,40,60,80,99 root primary
S3(config)#int vlan 99
S3(config-if)#ip address 172.17.30.23 255.255.255.0
S3(config-if)#no shut
hasilnya
sumber :https://prwahyukurniawan.blogspot.com/2016/07/2322-packet-tracer-configuring-rapid.html?m=1
Untuk lebih jelas, silahkan lihat videonya
Comments